US FREE 2Axis nema34 stepper motor cnc kit,1600oz 3.5A dual shaft 14mm CNC Rout

Description: Shipped from Germany&USA warehouse to EU members, no tariff, Fast shipment. This Item includes: 2PCS Nema 34 Stepper Motor with Dual shaft 1600oz-in holding torque, 3.5A,151mm14MM Shaft 2PCS Stepper Driver DQ860HA with 7.8A replacing DQ860MA,2PCS Power Suuply 350W 60V1PC Breakout Board&1PC DB25 Cable for free1, Stepper Motor 1 stepper motor:85BYGH450C-012B Electrical Specifications ：ModelStep angel( °)Motor LengthL(mm)Rate Voltage(V)Rate Current(A)Phase Resistance(Ω)Phase Inductance(mH)Holding Torque(N.m)Lead Wire(NO.)Rotor Inertia(kg.cm )Motor Weight(kg)85BYGH450C-012B1.81515.73.51.92211.342.455Part No.: 85BYGH450C-012B Dual shaft Frame Size: NEMA34Step Angle: 1.8 degreeVoltage: 5.7VCurrent: 3.5A/phaseResistance: 1.9 Ohm/phaseInductance: 22 mH/phaseHolding torque: 11.2N.m 1600oz-inRotor inertia: 3600g-cm2Number of wire leads: 4Weight: 5.5 kgLength: 151mm 2. stepper motor driver:DQ860HA Introduction: DQ860HA is a type of two-phase hybrid stepping motor driver, the drive voltage of it is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 7.8A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Holding torque when DQ860MA run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. Features:² High performance, low price² Average current control, 2-phase sinusoidal output current drive² Supply voltage from 24VDC to 80VDC² Opto-isolated signal I/O² Overvoltage, under voltage, overcurrent, phase short circuit protectio² 14 channels subdivision and automatic idle-current reduction² 8 channels output phase current setting² Offline command input terminal² Motor torque is related to speed, but not related to step/revolution² High start speed² High hording torque under high speed Electrical specification: Input voltage24-80VDCInput current＜ 6AOutput current2.8A～7.8AConsumptionConsumption：80W； Internal Insurance：10ATemperatureWorking Temperature -10～45℃；Stocking temperature -40℃～70℃HumidityNo condensation, no water dropletsgasProhibition of combustible gases and conductive dustweight500G Pins assignments and description:Connector Pins ConfigurationsPin Function Details PUL +,PUL-Pulse signal, PUL+ is the positive end of pulses input pin PUL- is the negative end of pulse input pin DIR+,DIR-DIR signal: DIR+ is the positive end of direction input pin DIR- is the negative end of direction input pinENBL+ Enable signal: ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver.ENBL-ENBL- is the negative end of direction input pin. Usually left unconnected (enabled) Function choice ( Using DIP pins to achieve this function) 1) Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table:SW5ONOFFONOFFONOFFONOFFONOFFONOFFONOFFSW6ONONOFFOFFONONOFFOFFONONOFFOFFONONSW7ONONONONOFFOFFOFFOFFONONONONOFFOFFSW8ONONONONONONONONOFFOFFOFFOFFOFFOFFPULSE/REV400800160032006400128002560051200100020005000100002500050000 2) Standstill current settingSW4 is used for this purpose. OFF meaning that the standstill current is set to be half of the selected dynamic current and ON meaning that standstill is set to be the same as the selected dynamic current. 3) Output current setting:The first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current. Select a settingClosest to your motor’s required current Output current (A)SW1SW2SW3PEAKRMSONONON2.802.00OFFONON3.502.50ONOFFON4.203.00OFFOFFON4.903.50ONONOFF5.704.00OFFONOFF6.404.60ONOFFOFF7.005.00OFFOFFOFF7.805.60 4) Semi-flow function:Semi-flow function is that there is not step pulse after200 ms, the driver output current automatically reduced to 40% of rated output current, which is used to prevent motor heat. Pins of motor & power:Motor and power pins1A+Motors wiring 2A-3B+4B-5,6DC+ DC-Power supplyPower supply ：DC24-80VDCThe peak input current can not up to 6A 3.POWER SUPPLY(350W 60V)350W Single Output Switching Power SupplyAC input range selected by switch.Protections:short circuit/overload/over voltage/over temperature 100% full load burn-in test Low cost,high reliability 1 year warranty Size: 215*115*50mmWeight:1.05kg AC input voltage range: 90～132VAC/180～264VACAC inrush current: cold start 25A/115V,50A/230VDC adjustment range:±10% rated output voltageOverload protection:105%～135%, hiccup mode, auto recoverySetup,rise,hold up time: 200ms,50ms,20ms/230VAC at full loadWorking temperature and humidity:-10℃～+60℃；20%～90 %RHModelDC output voltage,Current rangeVoltage toleranceRipple&NoiseEfficiencyS-350-6060V,0～5.8A±1%150mV83% 4. Breakout Board Set pins according to software as follows: Output pin: P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17. l P2 – X axis Pulse, P3 – X axis Direction l P4 – Y axis Pulse, P5 - Y axis Direction l P6 – Z axis Pulse, P7 – Z axis Direction l P8 - A axis Pulse, P9 - A axis Direction l P14 - B axis Pulse, P1- B axis Direction l P16 - C axis Pulse, P17- C axis Direction Input pin: P10 ,P11, P12, P13, P15 l Set them for Emergency Stop and X Y Z Limit switch

Price: 227.04 USD

Location: changzhou

End Time: 2024-09-02T06:33:40.000Z

Shipping Cost: 0 USD