TRON Flynn, Rinzler or Quorra - LEG Pieces Replica EL Panel + Driver

Description: Tron Leg Set This listing is for: 1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn or Quorra 2) Two pieces of shaped and angled EL Tape to go round the knees 3) Two pieces of 'Sacral 'shaped EL Panels to be placed at the lower back 4) Two pieces of 2cm x 25cm EL Tapes 4) A Powerful 8xAA battery EL Driver 4a) choice of power source for this Driver: I) Standard 8xAA Battery Box II) Rechargeable Li-ion Battery (smaller and lighter) with Intelligent Charger (Li-ion Batteries are only available in the UK due to airmail postal restrictions) 5) A 2 Way Splitter, 3 Way Splitter and 2 x 'Short, Medium and Long' Splitters 6) 1.5 metres of hook & loop tape - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable for washing. The set is currently available in Light Blue only at the moment Orange or Light Blue Dimensions of the products: If you are making a costume, it is a good idea to plan it out properly. For this set, the Driver/Inverter is very powerful and comes with a separate power pack So here are the dimensions of all the parts plus lengths of wire between them: THE POWER PACK Takes 8xAA batteries (not supplied) and is 12.7cm x 7.2cm x 1.9cm It has a 21cm thin power wire coming out of it that leads to the... DRIVER The Driver is 6cm x 4cm x 4cm It has the controls on it - Off, Flashing or On It has a 55cm wire coming out of it that leads to the... SPLITTER The Splitter is 40cm long in total, it is 20cm of wire which then splits into separate strands which are all 20cm long. A 3 Way Splitter attaches to the Driver One of these channels has a 2 Way Splitter attached that runs round the back to plug into the pair of EL Sacral pieces The other two channels have a special '3 way (Small Medium and Long) Splitter attached to them that run down each leg These SML Splitters have: one 'Short' channel that plugs to the 25cm Tape. Then the 'Medium' channel plugs into the Knee Joint section The 'Long' channel goes down to the Shin to plug into the Double Hoop The three pieces of EL Tape that run down the leg are: 1) SHIN This 15cm Double Hoop is designed to run from your shin to the ankle to give a great finishing touch to any Tron costume (these are also available for other parts of your Tron costume in our ebay shop) 2) KNEE JOINT Running up from the boot piece, this piece of EL Tape takes an angle round the knee, exactly as in the original costumes This has been made to largest size and will not fit everyone so it has been designed so you can just snip it down to the right size for you That's right, it really is as easy as just cutting the unwanted part off either or both ends (sealing the cut with sellotape, glue or clear nail varnish is highly recommended) 3) 2cm x 25cm EL Tape Another piece that can be cut to size is this straight piece of EL Tape that runs from the Knee Joint up to join the top half of the costume Coming from the 2 Way Splitter at the back of the costume: 3) EL SACRAL This pair of Panels sit at the base of the spine and look pretty awesome! The Tape is just 350 microns thick - that is 1/3rd of a millimetre! Sticky back hook & loop tape is supplied that is the exact width of the EL Tape. You must sew the other part of the hook & loop tape onto the costume making it very convenient to attach and remove Of course, you don't need to use the hook & loop tape, fix it any way you choose Please feel free to message us if you have any questions or would like planning your set. The whole kit is ready to use - just plug and play! A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from our ebay store VISIT OUR SHOP TO SEE OUR RANGE OF INVERTER/DRIVERS, SPLITTERS AND OTHER EL WIRE

Price: 49.99 GBP

Location: Cross in Hand, East Sussex

End Time: 2023-12-07T15:47:14.000Z

Shipping Cost: 3.79 GBP