Sea-doo 93-95 GTX GTI fuel and oil system tune up kit lines clamps carb screws

Description: Brand new fuel and oil line swap kit for Seadoo two stroke 3 seaters with 587-717 white engines. Also comes with stainless steel allen head internal/external carb screws. Everything you need to restore your fuel and oil systems and ensure better reliability and longer life from your Seadoo. Fits: 93-95 GTX , 93-96 GTI, 93-99 GTS If you have owned a seadoo for any length of time you know the gray lines destroy carbs and destroy engines, and maybe you have even seen the aftermath of them already (poor throttle response, bogging, eventually resulting in a blown motor). I have included a couple photos of what will inevitably happen to your carbs and filters if you don't change them, and also what often happens to the steel internal screws in the carburetors over time. Anyone who cares about their Seadoo and wants it to last should get rid of the gray fuel lines and the original oil lines ASAP. But it is also smart to clean out the carb filters at the same time, and while your doing that you should really consider changing the screws over to something a little more durable and a little more serviceable. This kit just gives you all the materials at once and speeds up the process. All this maintenance is relatively easy and does not require a professional. If you also need carb base gaskets and you are buying this kit, just send me an offer for a set of base gaskets (in my other items) for $5 and i will accept the offer. Just note that you also purchased this kit when you send the offer, to get the deal. Fuel lines: Includes USA black 30R7 HBD Thermoid ethanol resistant lines, all pre cut and labeled to make the fuel line swap as painless as possible for you. Also included are 15 made in USA Oetiker crimp clamps (OEM), which is more than you need for the entire fuel system (excluding vent lines). First step is to install lines on fuel selector and filter cap. From there you will just need to connect 3 lines onto your fuel baffle by matching up the labels on the lines to those on the top of the baffle. Then you will simply route the lines through and connect them to the carb inlet and return, which are also labeled. The carb return will be toward the back of the ski. The lines are measured to fit the machine advertised and cut straight. The Oetiker clamps do a superb job of sealing and preventing leaks, and offer serious durability. Leaks are extremely dangerous on a jet ski, there is a reason bombardier uses these at the factory. Oil lines: Made in USA Tygon 4040F fuel and oil resistant line. Oetiker made in Germany OEM double pinch clamps. Pre cut for 587-717 engines, just push lines on and gently crimp clamps and you are done. The oil pumps do not normally fail, the original lines do. If your oil lines still have paint on them, you are on borrowed time, and lubrication failures are never cheap. Carb screws: Stainless steel allen head USA made hardware to eliminate corrosion and eliminate stripped fasteners during rebuilds. Includes the following, which is everything needed to replace all fasteners (inside and out) on a dual carb setup. If you have a single carb let me know and I can slightly reduce the price, or you can just have extras. 2- Stainless Seat retaining screw - allen head 2- Stainless lock washer 2-Stainless Needle retaining screw- phillips head 2-Stainless Metering block check valve screw- allen head 2-Stainless Flat washer 4-Stainless Metering block retaining screws - allen head (the factory screws always strip due to a combination of corrosion and their phillips head, but these will have neither issue) 8-Stainless External Cover screw, metering side- allen head (the factory screws are stainless but strip due to phillips head being unable to handle removal torque) 8-Stainless External Cover Screw, fuel pump side - allen head (same as above, get rid of the phillips head). Includes 4 long and 4 short for the non pump side. 8- Stainless Lock Washer 4- Stainless Flat Washer Give me a call if you have any questions before purchasing or during installation etc, I am happy to help. All this is relatively easy and I have done my best to put this together so that the average person can do this maintenance on their own, without having to pay a dealer, etc. I also can put this kit together for just about all years and models, so just send me a message or give me a call if you need this same kit for a different year and model than I have listed. Blake: 989-492-8053

Price: 70 USD

Location: Saginaw, Michigan

End Time: 2024-08-13T21:36:42.000Z

Shipping Cost: 10 USD