RF Remote Control 12 pcs Receiver 12 Button 1 Button 1 Receiver 1 to Multi RX

Description: Brand:Eletechsup Product Name : RF Remote Control 12 pcs Receiver 12 Button 1 Button 1 Receiver 1 to Multi RX Qty : 1 pcs 12 Button Fixed code remote ; 12 PCS 1 Chancel Receiver . Every button controls 1 pcs Receiver independently : Wireless Receiver : Technical indicators: 1.operating voltage: DC 12V ; 2.working frequency:433.92MHz; 3:Maximum load: 1000 watts; 4:PCB Size:41×20×15mm; 5: Momentary Mode ,Latch Mode , Toggle Mode can be adjustable by slodering back side. 6. Pls connect the receiver modules properly before power supply ; 8: Momentary Mode ,Latch Mode , Toggle Mode can be adjustable by jumper . 9. Pls connect the receiver modules properly before power supply ; 10: 1 chanels; 11: Learning function (can works with EV1527 and PT2262 remote , can store 16 pcs different code remote ); Advantage : 1: Receiver Mother board have a learning key , if the remote is lost ,must buy EV1527 Learning remotes to re-learn; Output: A.singnal Inter-locking (Latch)----connect 2and 3 ; B.singnal Self-locking (Toggle) ---- connect 1 and 2 ; C.singnal Non-locking (Momentary )---- All disconnect ; · Toggle : Press->On; Press again->Off ; · Latched : Press->On; Press other button->Off ; · Momentary : Press and hold->On; Release->Off ; Relay mode : Normally close (NC ) ; Normally open (NO ) ; Normally-open (NO)contacts connect the circuit when the relay is activated; the circuit is disconnected when the relay is inactive. It is also called aForm Acontact or "make" contact.NOcontacts may also be distinguished as "early-make" orNOEM, which means that the contacts close before the button or switch is fully engaged. Normally-closed (NC) contacts disconnect the circuit when the relay is activated; the circuit is connected when the relay is inactive. It is also called aForm Bcontact or "break" contact.NCcontacts may also be distinguished as "late-break" orNCLB, which means that the contacts stay closed until the button or switch is fully disengaged. Learning method and steps 1.Keep pressing learnig key on receiver board , release the button when LED is off , enter the learning state ; 2.Press any key on remote control within 5 seconds , LED flash 3 times and then turn on , then ithave success in learning. Clear the deposit information Keep Pressing Learning Key , LED turns off , Wait 10 Seconds , LED turn on ,that deposited information has been successfully cleared ; Transmitter Remote : Qty : 1 pcs 12 Button Fixed code remote ; Features / Specifications : 1. 12 buttons; 2. High stability, SMT chip, frequency stabilization SAW, 5 ultra-high-frequency transistor; 3: Large power; Technical Data : TransmitterModule No.:AK009; Power supply : 12V 23A batteryreplacable.(This remote doesnot have a battery , Please buy in your local market ) Operating current:≤ 10mA; Transmit Power : 10mW; Oscillation mode:SAW resonator; Modulation mode:ASK/OOK; Operating frequency:433.92MHZ; Encoding format: PT2264 fixed code (compatiable for PT2262 SC2262 PT2260 ); RC Resistance : 4.7M; SAWFrequency stability:±75KHZ Remote distance : 100-500 meter ; Wiring Diagram 1: DC 12V control circuit,Wiring diagram below. "LOAD" may be LED lights, fans, motors and other DC 12V Wiring Diagram 2: DC 1-48V OR AC 85-265V control circuit,Wiring diagram below(Note:If not DC 12V load, need another DC 12V power supply). "LOAD" may be LED lights, fans, motors and other DC AC equipment

Price: 11.99 USD

Location: Guangzhou

End Time: 2025-01-01T03:15:32.000Z

Shipping Cost: 0 USD