Description: This sale is for a gallon of Multi-Sheen finish Hot Rod Black Paint (SMR-456) and a quart of slow activator; which yields 1.25 gallons sprayable. The SMR-456 is a 2.8 lbs/gallon voc. SMR-456 Hot Rod Black is a 2 component acrylic urethane coating. It mixes 4:1, 5:1 or 6:1 (changes gloss level) with a 5-10% optional reduction with zero voc Urethane Grade Reducer. SMR-456 Hot Rod Black is an excellent coating for a High Quality Black satin Finish. This coating is formulated to withstand the same atmospheric conditions as a high quality single stage urethane topcoat. FEATURES: .True 2K Urethane Durability .Uniform Jet Black Color .Excellent Exterior Stability from UV Light .Fast Dry .Easy Mix Ratios .Chemical Resistant Finish .Great Rub Resistance MIX RATIO: SMR-456 is activated with SMR-150 (Medium Activator) or SMR-170 (Warm Activator) at a 4:1, 5:1 or 6:1 mix ratio wit a 5-10% optional reduction with zero voc Urethane Grade Reducer. High Sheen (Low Gloss) 4 Parts Hot Rod Black 1 Part ACTIVATOR 5-10% (Optional) zero voc URETHANE GRADE REDUCER Medium Sheen (Eggshell) 5 Parts Hot Rod Black 1 Part Activator 5-10% optional zero voc reducer Low Sheen (Satin) 6 Parts Hot Rod Black 1 Part Activator 5-10% optional zero voc reducer GUN SETUP Fluid Tip psi HVLP Spray Gun 1.3 – 1.4mm 8-10 psi Conventional Gravity Feed 1.3 – 1.4mm 25-30 psi SURFACE PREPARATION: Surface should be cleaned of all grease, oil, dirt, rust, etc before applying SMR-456 Hot Rod Black. Wash area with soap and warm water. Thoroughly clean area with Wax and Grease Remover. Scuff surface with a red scuff pad or equivalent. Reclean with wax and grease remover. Do not use coarse grit sandpaper. Apply a pre-treatment primer and allow to dry. Apply primer surfacer and allow to cure. Sand primer surfacer with 180-220 grit sandpaper. If applying a sealer over the primer surfacer, finish sand with 320-400 grit sandpaper. If applying SMR-456 Hot Rod Black directly over the primer surfacer, finish sand with 400-500 grit sandpaper. APPLICATION Apply 1 full wet coat followed by 1 medium wet coat. Allow 5-10 minutes flash time between coats. Do not apply Hot Rod Colors in temperatures over 80 deg. F! This causes an un-even finish (stripping). Dry Times: Dust Free: 5-10 minutes depending on temperature and activator selection Tack Free: 5-10 minutes Force Dry: 10 minutes @ 120°F (49°C) Delivery: Air Dry: 6-8 hours Bake: After cool down Time to stripe: Air Dry 6-8 hours (special care should be taken for first 24 hours) Bake 1 hour after cool down Time to decal: Air Dry 24 hours Bake 24 hours Time to recoat Air Dry 24 hours @ 70°F Bake After cool down Health and Safety: See Material Safety Data Sheet and labels for additional safety information and handling instructions. * The contents of this package may have to be blended with other components before the product can be used. Before opening the packages, be sure you understand the warning messages on the labels and MSDS’s of all components, since the mixture will have the hazards of all its parts. * Improper handling and use, for example, poor spray technique, inadequate engineering controls and or lack of Personal Protective Equipment (PPE), may result in hazardous conditions or injury. * Follow spray equipment manufacturer’s instructions to prevent personal injury or fire. * Provide adequate ventilation for health and fire hazard control. * Follow company, product MSDS and respirator manufacturer’s recommendations for selection and proper use of respiratory protection. Be sure employees are adequately trained on the safe use of respirators per company and regulatory requirements. * Wear appropriate PPE such as eye and skin protection. In the event of injury, see first aid procedures on MSDS. * Always observe all applicable precautions and follow good safety and hygiene practices. On Nov-19-13 at 08:47:28 PST, seller added the following information:
Price: 160.55 USD
Location: Dayton, Ohio
End Time: 2024-09-01T18:41:52.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: 20%
Return shipping will be paid by: Buyer
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Paint Type: Acrylic Urethane
Brand: Speedokote
Manufacturer Part Number: SMR-456/170
California Prop 65 Warning: WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. ADVERTENCIA: Cáncer y daño reproductivo - www.P65Warnings.ca.gov.
Type: Single-stage Paint
