For 2010-2016 Honda CR-V CRV 2.4L Radiator Cooling Fan LH Driver Side HO3115155

Description: SAFE & SECURE SHOPPING 100% SATISFACTION GUARANTEED FAST SHIPPINGRadiator Cooling Fan LH Driver Side For 2010-2016 Honda CR-V CRV 2.4L HO3115155 Product Description Features:1.Drop in replacement for easy installation.All units are test-fitted into the corresponding condenser to ensure precise, consistent fit. Redesigned shrouds and brushless motors, simplify installation and increase fan performance.2.Ideal replacement.This engine cooling fan assembly was precision-engineered to match the fit and performance of the stock radiator fan assembly on specific vehicles.3.Statically and dynamically balanced preventing assembly misalignment and excess noise for quiet operation.Shrouds are ribbed which increase strength and rigidity of the entire assembly under load forces from airflow thrust and rotating blade torques.4.All fan assemblies are durability tested for countless hours at elevated temperatures above 260°F as well as being wind tunnel tested to ensure a direct match to the original fan assembly for cooling airflow versus input amperage.Ensure reliable performance for the life of the vehicle.5.Trustworthy manufacturing for far less than same part at the dealership. Specifications:Material:PlasticColor:BlackInstallation position:directly behind radiatorQuantity of Blade:5Connector Terminal Quantity:2pinVoltage:12Fitment Type:Direct Replacement Part Numbers:621-438, 621438, 19015REZA01, 19020RSAG01, 38616RB0003, 19015R5AA01, 38616RB0003PFM, HO3115155, TYC601330 Fitment:For 2011, 2015-2016 CR-V SE 2.4L L4For 2012-2016 CR-V Touring 2.4L L4For 2010-2016 CR-V (submodel: EX, EX-L, LX) 2.4L L4 Package Contents:1 × Radiator Cooling Fan Attention:The radiator cooling fan is an integral part of your car that is responsible for cooling the radiator of your car. The radiator cooling fan does this by either pulling or pushing air into the radiator keeping the radiator temperatures within the safe levels. A damaged radiator cooling fan is a determining factor in preventing your car from overheating. Below are the materials that you need along with the instructions on how to replace a radiator cooling fan.Step 1: Locate the Radiator Cooling FanLocating the radiator cooling fan is the first step in replacing it. Turn off your car and allow it to cool off. Open the hood of your car and you will be able to see the radiator that is located at the back of the grill at the front portion of your engine compartment. The radiator cooling fan is attached at the back of the radiator through a mounting frame. Under the engine and the radiator is a sticking cylinder that is encased in a small casing. That is the radiator cooling fan motor that you may need to change or repair other than the radiator cooling fan itself.Step 2: Disconnect the Power SupplyOn the fan motor is an electric cable running towards the engine. Find the connector of the wires from your engine and from your radiator fan motor and disconnect it. Using two masking tapes with different colors, note the connection of the wires so that you will not have a hard time reconnecting the wires later.Step 3: Remove the Fan HousingUsing a crescent wrench, remove the four screws located at each corner of the fan housing. Remove the fasteners at the sides of the fan housing as well. A radiator cooling fan housing is relatively large and you may need to remove all the obstructions like hoses and wirings so that you can extract the fan housing off your car hood. Hold the housing firmly and lift it off your engine compartment. Be careful in removing the fan housing to avoid damaging it. Place the fan housing on a clutter-free working table.Step 4: Remove the Radiator Cooling Fan and the Fan MotorThe fan blade is either pinned or screwed to a shaft. With a screwdriver, loosen the fan blade and slide if off its shaft. You may need to remove a keeper that prevents the fan blades from moving up in the shaft up and down. As to the fan motor itself, remove it from the fan housing using a screwdriver.Step 5: Attach the Replacement Radiator Cooling Fan and Fan MotorInstall the new fan motor into the fan housing. Slide your replacement radiator cooling fan into the shaft, insert the keeper and secure the new cooling fan and keeper into place. Return the fan housing back into its proper place and secure the screws and the fasteners. Reattach the hoses and wires you removed in step 3. Connect the fan motor into the car electrical system using the electrical tape guide you made in step 2. Note:You may notice that the Cooling fan needs diagnostics by the following signs:1. the engine is overheating.2. the fan sensor is functioning incorrectly.3. the engine loses power at higher RPM.4. "Check Engine" flashing on the dashboard. Please Carefully Check Whether the OE Number And Picture are What You Need Before Buying. If You are Not Sure Whether It Fits, Please Write to us. If There are Any Problems, Communication by Letter Will be More Effective. No Instruction Included, professional installation is highly recommended. ShippingReturnsContact UsShippingItem will be shipped within 1-2 working day of payment cleared. We ship item from our UK warehouse by UK Royal mail Standard delivery.All items will be checked strictly before shipping and it will be shipped to your PayPal address.Estimated delivery time is 4-8 working days (Not including weekend or public holidays)Delivery times may vary particularly during peak periods or unexpected weather conditions. In event of a very unlikely slight delay, your patience would be highly appreciated.We do not provide pick up or local collection service so far. ReturnsWe accpet return within 30 Days of dispatch.For exchange buyer MUST return the defective item for 1 to 1 exchange, return cost due to buyer.We do not cover defects and/or damage resulting from normal wear and tear of the equipmentor otherwise due to the normal ageing of the equipment, including battery deterioration.For free shipping means we paid the shipping fee on your behalf, that fee will be deducted.In case return cause by wrong buy, return postage will be at buyer side also.Please contact us immediately about any your return before shipping back the Once the item has shipped the regular return policy applies. Notifying us ahead of time will help us to ensure that your return is dealt with promptly upon arrival. Packages that arrive without our return format may be returned to sender. Contact UsAll messages will be answered within 24 office hours.Please contact us either by clicking "contact seller" in the "purchase history" section or simply click "ask a question" at the bottom of this page.If you are unsatisfied with our item or service, please contact us before leaving any feedback. We are committed to resolve all issues in a friendly and satisfactory manner. We always reply to messages within 2 business days (off-duty at weekend). If you do not get a response from us, then please check your junk or spam mailbox. Copyright © 2022 Tongtool

Price: 49.99 USD

Location: Perth Amboy, New Jersey

End Time: 2025-01-15T17:32:51.000Z

Shipping Cost: 0 USD