Description: APPLICATION: 1963-1974 Corvette - Small Block Chevrolet - 1-5/8 x 3 in. FEATURES: Fuel Economy From The Engine Leakproof O-Ringed Port Seals Leak Test For Max Performance Mandrel-Formed Power Plenum Include All Mounting Hardware Constructed of .049 cold roll flash mild steel tubing READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING: For ease of installation, your vehicle must be raised a minimum of 36". Warning: should you decide to install any exhaust product yourself, be warned that the original equipment jack that came with the vehicle is intended for emergency use only. The use of a frame jack in conjunction with a floor jack as main support is highly recommended to minimize the accidental dropping of a vehicle while the installation proceeds. Never go under any vehicle that is supported by only a bumper jack! 1. PREPARE THE VEHICLE FOR INSTALLATION: A. Disconnect the negative terminal at the battery to prevent accidental damage to the electrical system. Disconnect the battery cable at the starter. B. Remove the air cleaner and the hot air tube. C. Disconnect the automatic choke exchange tube. D. Remove the spark plugs on both sides of the engine. E. Unbolt the headpipe from the stock exhaust manifolds and move aside. Remove the stock exhaust manifolds. F. Remove the old port gaskets, if equipped. Clean the exhaust port surfaces of any debris. 2. CHECK THE CONDITION OF THE MOTOR MOUNTS INSTALLATION NOTE: It is recommended that new motor mounts be installed before installing the headers. 3. INSTALL RIGHT SIDE HEADER FROM BELOW: A. Work the header up through chassis into position B. Place the gasket into position and check the port alignment. C. Install the front and rear header bolts (supplied). Do not tighten. D. Install the balance of the header bolts (supplied). Do not tighten. E. Tighten all header bolts progressively and evenly until they are tight. F. If the generator/alternator was mounted to the exhaust manifold, use bracket, see illustration "A". G. Air-conditioning equipped vehicles with the head-mounted compressors must modify the bracket, see illustration "B". INSTALLATION NOTES: 1. If the stock bracket is different than the unit shown in illustration "B," use bracket. 2. To mount the compressor, use the stock stud with a 1-ΒΌ" long tube spacer and install as illustrated. 4. INSTALL LEFT SIDE HEADER FROM BELOW: A. Place the gasket into position and check the port alignment. B. Install the front and rear header bolts (supplied). Do not tighten. C.Install the balance of the header bolts (supplied). Do not tighten. D.Tighten all header bolts progressively and evenly until they are tight. E. If engine is equipped with a radiator reservoir mounted to the stock exhaust manifold use generator bracket to install. See illustration "D". 5. AFTER HEADERS ARE IN PLACE: A. Inspect all points with limited clearance. Relocate any points that have direct contact with the headers. Make sure there is adequate Clearance around all lines (transmission, brake, fuel and electrical wires). Reroute as necessary. Before installing your exhaust system, replace any fluids that you may have removed or lost. B. All engines may not be mounted exactly the same from the factory. It may be necessary to loosen the motor mounts and position the engine slightly to one side or the other to obtain maximum clearance. At this time repeat step two, inspect motor mounts. C.Reconnect battery cable at the starter. D.Bolt the reducer adapters (using the gasket, nuts and bolts supplied) to the collectors. E. Connect the exhaust system by either clamping or welding the exhaust pipes to the reducer adapters. INSTALLATION NOTES: 1. If the vehicle was equipped with a smog pump connected to the stock exhaust system, it will be necessary to modify the header collector. See illustration "D". Drill a 5/8" hole into the collector, and weld a piece of 5/8" tubing into position. Cut the original tube coming from the air pump at a straight section. Connect tubing to the collector with a piece of 5/8" neoprene hose. Secure with hose clamps. 2. If the vehicle is equipped with an aluminum case powerglide transmission, it will be necessary to reroute the driver's side exhaust as it exits the reducer. Shift linkage clearance as needed when the transmission is in the parked position, see illustration "E". 3. Reconnect the negative battery cable at the battery. After you have finished installing your JT headers, take the vehicle for a road test. Listen carefully for any exhaust leaks or other strange noises and make corrections. When the vehicle has been driven for a few days, retighten the header bolts. We find that periodically checking the bolts will prevent the flange from warping and the burning out of the header gaskets. Note: The items you received are shown in the figure. If you have any questions later, please contact the after-sales staff in time.
Price: 180 USD
Location: Pooler, Georgia
End Time: 2025-01-06T03:54:01.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Collector diameter: 3 in
Mounting Style: Bolt-On
Items Included: Mounting Hardware
Color: Black
Bolt Size: 3/8-16 x 3/4
Manufacturer Part Number: JUTAUTO151
Material: Mild Steel
Item Length: Long Tube
Placement on Vehicle: Front
Fuel Type: Gasoline
Brand: JUTAUTO
Type: Exhaust Header
Substrate Material: Mild Steel
Manufacturer Warranty: 1 Year
Primary diameter: 1-5/8 in (42mm)
Features: CERAMIC COATED
Country/Region of Manufacture: China
Engine: Chevrolet Small Block Gen I
Performance Part: Yes