Description: MAX BOND THIXOTROPIC A/BHalf Gallon Combined Volume 64 Fluid Ounces(1 Quart Resin And 1 Quart Curing Agent)Packaged In Wide Mouth Jars Up To 140 to 150 Square Feet Per Gallon Coverage(0.010 Inch Bondline Thickness)High Strength Epoxy Adhesive ForWood, Metals, Concrete, Fiberglass, Plastics, Stone And MasonryNon-Sag-Thixotropic Paste Consistency (Will Not Flow At Rest But Easily Spread By Hand). DESCRIPTIONMAX BOND THIXOTROPIC A/B is a two-part modified epoxy/polyamide based adhesive system specially formulated to provide structural bond strength to a variety of substrates. It is a thickened version of the MAX BOND System. Its consistency allows for the mixture to be applied onto a vertical or overhead application with minimal drips or runs. MAX BOND THIXOTROPIC A/B exhibits structural bond strengths to numerous substrates commonly used in composites industry such as steel, aluminum, metals and alloys, resin impregnated composites, and most plastics. It performs well in wide range of service temperature and resists cracking and delamination due to cyclic vibration, thermal expansion and contraction.Conforms To Hundreds of Aerospace/Military/Naval Materials SpecificationsMIL-A-8623 T1MS-511MMM-134 Type1 and Type 2OS-9923ABoeing BMS-5-29NASA Requirements For Low Outgassing Polymers(<1% CVCM, collected volatile condensable material )Tested For Aerospace Application Under NASA Low Outgassing Specifications of less than 1% CVCM, TMLV requirement Conforms To Code Of Federal Regulations FDA CFR Title 21 175.300 For Direct/indirect Food Contact Adhesive MAX BOND THIXOTROPIC A/B Utilized As A Structural Adhesive For Bonding Wood And Steel Structural Bonding With MAX BOND THIXOTROPICAvailable Kit SizesMAX BOND THIXOTROPIC A/B 32 Oz KIThttps://www.ebay.com/itm/222624260837MAX BOND THIXOTROPIC A/B 64 Oz KIThttps://www.ebay.com/itm/311946479917MAX BOND THIXOTROPIC A/B 1 GALLON KIThttps://www.ebay.com/itm/222624293631MAX BOND THIXOTROPIC A/B 2 GALLON KIThttps://www.ebay.com/itm/222623988841For food contact applications, MAX BOND THIXOTROPIC A/B must be fully cured to ensure no chemical leaching can occur when foodstuffs' come in contact with the cured resin system. Any uncured chemical compounds from the improperly prepared MAX BOND THIXOTROPIC may be extracted and cause cross-contamination or leaching during food contact. Please review the following use instructions to avoid any curing problems.Check for resin crystallization. During the colder season, the MAX BOND THIXOTROPIC resin component or PART A may crystallize and must be heat-processed to fully polymerize the resin system. Inspect the PART A bottle for any turbidity or a solid mass that typically forms on the bottom of the bottle. Processing Crystallized Epoxy Resin Video will open in a new window [isdntekvideo] Obtaining adequate bond strength when bonding plastic-to-plastic substrates or plastic to dissimilar substrates is often a challenge for epoxy bonding In general plastic surfaces demonstrates poor ‘wettability’ or the ability of a liquid to form a continuous film. These types of substrates or are called LSE or Low Surface Energy substrates and in general, most thermoplastic surfaces fall into this category. Teflon or its generic name PTFE and other polyethylene derivatives such as HDPE, LDPE, UHMW and olefinic-based plastics demonstrate poor liquid wettability due to its low surface energy. To create a viable bondable surface condition for these types of plastics, it must be surface treated by creating a superficial oxidized surface to increase its dynamic surface tension. Various types of physical treatment can be used to increase the surface energy of plastics, mostly through oxidation of the superficial layer. Flame treatment is the most widely used and cost-effective pre-treatment for polyethylene (HDPE, LDPE, UHMW) and polyolefin-based plastics prior to polymer bonding or printing. The resulting change of the surface by creating an oxidized layer onto the substrate greatly improves the ability of liquids wet-out the surface thus creating a strong adhesive bond between the surface and the coating. A Flame Treating process consists of exposing the surface to a suitable oxidizing flame for a period in the range 0.2 to 3.0 seconds. This treatment brings about a change to the polymer surface that increases its surface energy allowing fluids to effectively wet-out the surface and permits a strong adhesive molecular and mechanical bond.Flame Treating Using A Commercially Available Propane Torch Adjust the propane torch so that a low oxygen burning flame is achieved and pass over the area to be treated several times until a slight haze is noticed on the surface of the substrate. Using A Dyne Pen To View The Improve Surface Wetting Of the Untreated And Flame Treated UHMW plastic. Flame Treating the plastic substrate will make adhesion possible and create a strong bond. Flame Treated Surface Ideal For Bonding Joint Designs For Best Adhesion Performance Joint and Bonding And Design Suggestions Load Testing For Tensile Shear Strength of the Adhesion Types of stress load For Concrete Koi Pond Construction And RepairStones And Decorative Boulders Were Bonded In Place WithMAX BOND THIXOTROPIC A/B Suitable For Continuous Under Water Applications Plywood Aquarium Construction WithMAX BOND THIXOTROPIC A/BAdhesive Cures To Structural And Waterproof Bond 500 Hundred Gallon Plywood Aquarium StorageSecure the caps for both bottles after use and store above 65°F minimum temperature to prevent re-crystallization. The resin system will remain viable for at least 12 months or longer when stored properly.The PART A or resin component may 'crystallize' after prolonged storage. Please inspect the PART A bottle for any solid crystallization that will appear on the bottom of the bottle. For our complete listing, please Visit our eBay store! PLEASE CHECK OUT OTHER AVAILABLERESIN SYSTEMS AT OUR eBay STORE IMPORTANT NOTICEYour purchase constitutes the acceptance of this disclaimer. Please review before purchasing this product. The user should thoroughly test any proposed use of this product and independently conclude satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval. The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, Polymer Composites, Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use. There is no warranty of merchantability or fitness for use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to refund of the purchase price or replacement of the product within the agreed warranty period. Polymer Composites, Inc. and its direct representative will not be liable for incidental or consequential damages of any kind. Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.
Price: 59.13 USD
Location: Ontario, California
End Time: 2025-01-25T20:23:27.000Z
Shipping Cost: 0.72 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
MPN: MAXTHIXO64OZ
Modified Item: No
Mix Ratio: 1:1 By Weight Or By Volume
California Prop 65 Warning: EPA SARA Title III Section 313 (40 CFR 372) Component(s) above ‘de minimus’ level: None US California Safe Drinking Water & Toxic Enforcement Act Proposition 65: This product does not contain any chemicals known to the State of California to cause cancer, birth defects, or any other harm.
Brand: MAX EPOXY RESIN SYSTEMS
Type: Strutural Adhesive
Working Time: 70 to 85 Minutes @ 72°F
Unit Type: fl oz
Non-Sag-Thixotropic Consistency: Will Not Flow At Rest But Easily Spread
Cure Time: 24 Hours At 72°F Or Heat Cured For Faster Cure Time
High Strength Epoxy Adhesive For: Wood, Metals, Concrete, Fiberglass, Plastics
Model: MAX BOND THIXOTROPIC A/B
Country/Region of Manufacture: United States
Unit Quantity: 64
