CMW 8000 Lithium Moisture Vapor Barrier and Concrete Densifier

Description: CMW 8000 Lithium Moisture Vapor Barrier and Concrete Densifier Product Description CMW 8000 Lithium Moisture Vapor Barrier & Densifier CMW 8000 Moisture Vapor Barrier is a clear, colorless spray applied penetrating lithium Potassium silicate blended system designed to stop concrete floor coatings and floor coverings from de-bonding due to hydrostatic vapor pressure coming up through a below grade concrete slab, on-grade slab and elevated deck slabs. This system stops hydrostatic pressure, capillary action and moisture migration by creating a negative and positive side moisture barrier. The CMW 8000 is used prior to application of a floor coating or floor covering where excess moisture coming up through the concrete is a potential problem. The CMW 8000 may be painted, epoxied or stained over, and will accept concrete topping or mastics for floor tile etc. The CMW 8000 is also used in joint repairs prior to application of the 3246 Expansion Joint , our two Control Joint Fillers 3003 and 3004 to keep moisture from the joint repair. CMW 8000 is a lithium potassium silicate blended sealer that with its small molecular structure, penetrates deep into the concrete slab. A reaction occurs between the lime and excess Portland cement, which is always present, and forms Calcium Silicate Hydrate (CSH). This process will encapsulate the moisture to create a permanent break in the capillaries of the concrete, stopping the passage of liquids and vapors through the concrete. As a densifier, the CMW 8000 adds 20% - 40% increase in density to the concrete while increasing the strength of the cured concrete. CMW 8000 will purge alkalai salts and contaminents to the surface over a several day period and help eliminate existing effllorescnce problems from reocurring. It can also be combined with a water repellent treatment for superior protection. CMW 8000 comes in both a Ready-to-Use and Concentrate version. The ready-to-use formula needs no mixing and can be used straight out of the container. The CMW 8000 concentrate version comes in a 5 gallon pail which makes 20 gallons & 55 gallon drum which makes 220 gallons of ready-to-use product (3:1 mix ratio - mix 3 gallons water with each 1 gallon concentrate). For projects requiring a maximum level of moisture control or need to meet meet ASTM F3010 specifications for vapor permeance, consider using the CMW 8000 as the base level of protection followed up with a single coat application of the E1409CL Moisture Vapor Barrier Epoxy Primer or the MV2112 Moisture Vapor Barrier Epoxy Primer , The CMW 8000 adds additional protection to the E1409CL and MV2112, both of which meet the ASTM F3010 specification and can hold up 20 psi vapor pressure but in areas with significant moisture issues the CMW 8000 can help lower the potential risk of problems. The E1409CL and MV2112 would then be topcoated with your polymeric coating or resiliant flooring system. Where is CMW 8000 used? Concrete Driveways Concrete warehouse, factory, retail floors Basement and garage floors Retaining walls & concrete tanks pre-treatment Used prior to application of floor coating, covering, tile or primer Efflorescense problem areas Prior to application of Polyurea coating systems “Out-Gassing” reduction Below grade concrete – positive & negative side Why CMW 8000 Moisture Vapor Barrier? Blocks moisture vapor and hydrostatic pressure reducer Used in joints to stop vapor/water pressure damage to joint materials Permanent - becomes part of the concrete Stops minute fracture weeping of moisture (may require several coats) In areas of high humidity and salt air - reduces corrosive activity to rebar within concrete Stops effloresence – purges salts and residual acidic materials out Insure longer lasting floor coatings in areas of vapor pressure Apply to new or old concrete Improves concrete strength and chemical resistance Reduce and eliminate hairline & curing cracking in new concrete Assists in uniform curing on new concrete via chemical reaction Acts as adhesion promoter for surface applied coatings Does not change surface appearance Helps concrete stains retain color longer Non-toxic, non-flammable, no voc and no odor Why Lithium Silicate vs Potassium or Sodium Silicates by ConcreteConstruction.net TECHNICAL INFORMATION Color Clear, No change in appearance or surface texture Sheen/Gloss Level None Re-Coat When Damp 30-45 Minutes #Coats Recommended # coats depends on porosity Back in-service time 1-2 hours walk or drive on Application method Low pressure hand pump or airless sprayer Low Application Temperature 35F|1.7C Surface & Air Base Water VOC Content 0 g/L Use on Material Concrete Coverage Rate Square Feet/Gallon New Fresh Concrete 325 - 400 Rough Slab Finished Surface, Cured Concrete 50 - 150 Steel Trowel Smooth Finish, High Density 150 - 250 Coverage is dependent on the profile of the surface and porosity of the substrate Size Finish Price Concentrate - Makes 220 Gallons None: No Change Surface Appearance 3,449.99 Ready-to-Use 5 Gallons None: No Change Surface Appearance 247.25 Ready-to-Use 1 Gallon None: No Change Surface Appearance 62.10 Concentrate - Makes 20 Gallons None: No Change Surface Appearance 460.00 Shipping Shipping cost:No cost shipping lower 48 US States FedEx Ground Delivery time:Typically 3-5 days to process order plus 1 to 5 days transit time after shipment depending on location Payment We accept the following payment methods: PayPal payment due at time of order placement Please contact us if you have any questions. Service PLEASE CONTACT CUSTOMER SERVICE FOR QUESTIONS

Price: 62.1 USD

Location: Santa Ana, California

End Time: 2023-09-19T14:22:48.000Z

Shipping Cost: 0 USD