AQUATEC 8851 RO BOOSTER PUMP 8851-2J03-B421 + TRANSFORMER + 1/4" PORT SWITCH

Description: WHAT YOU WILL RECEIVE ONE (1) NEW AQUATEC 8851 SERIES RO BOOSTER PUMP WITH 3/8" JG INSERTS PART NUMBER 8851-2J03-B421INPUT/OUTPUT 3/8" QUICK CONNECT24 VACONE (1) NEW 8800 TRANSFORMER 115VPART NUMBER: TACS 114-48ONE (1) NEW AQUATEC PRESSURE SWITCH FOR 6800 AND 8800 BOOSTER PUMPS 1/4" QUICK CONNECTSPART NUMBER: PSW 240MADE IN THE USA CLICK BELOW FOR YOUR WARRANTY AND INSTALLATION INSTRUCTIONS(requires Adobe Reader: it's free) Get It Fast!! Get a Tracking Number!!For Only $57.00 More, Select USPS Priority Mail at Checkout and Receive Your Item in 2-3 Days and Get a Tracking Number and Up to $50 Insurance Protection.NOTE: USPS does not offer tracking numbers for First Class shipping.WARNING: Domestic USPS packages are not insured unless Priority Mail or Express shipping are purchased. Don’t pay more for less!We ship sooner, faster, and for less than our competitors.We ship immediately.We charge you less than our competitors charge you for slower service.We combine shipping upon request.We will match all verified competitor's prices.We ship internationally.Service makes the difference! BETTER PUMPS BETTER LIVING PUMP TYPICAL APPLICATIONS Water Treatment/RO Carbonation Systems Misting Systems Alternative Energy/Solar Medical Labwater Laser Cooling Systems Fuel Cells USE AND BENEFITSThis pump is usually used to boost water supply pressure to a Reverse Osmosis water system. If your water supply pressure is below 40psi, you should add this pump to your RO system.This water booster pump is to boost the input water pressure. It is usually used to increase the input water pressure for Reverse Osmosis systems. (boost pressure to 60 to 80 psi).This pump is suitable for RO systems that use up to a 120GPD membrane.For RO systems, an increase in input pressure means an increase in water production and water purityRO systems will run more efficient, with less waste water. Since it uses a pressure switch and solenoid valve to turn on/off the water input, it can turn on and turn off more accurately than the mechanical auto shut-off valve.For large water containers or an open water tank, you can use a float switch or level switch to control the operation of the pump. Product Data Sheet: Aquatec.comWarranty Statement: Aquatec.comInstallation Instructions: Aquatec.com Aquatec's original product, and still the "global standard" in booster pump technology, providing reliable inlet pressure for efficient membrane utilization.These pumps are capable of continuous duty and are effective for recirculation based applications as well. They are ideally suited to work with hydro-pneumatic storage systems but are compatible with most hydraulic shut-off valves also. These pumps are commonly used with one or more of Aquatec's flow control components including: pressure switches (PSW Series), tank level controllers (TLC Series) or electronic shut-off valves (ESO Series). FAQ for RO BOOST PUMPS and DELIVERY PUMPS:Q. The R.O. system is not working properlyA. See IMI 147, R.O. Boost Pump Troubleshooting guide: Aquatec.comQ. The CDP, Continuous Duty Pump, runs continuously. A. See IMI 156, Automatic Shut Off Valve’s effect on the PSW’s shut off abilityQ. The pump that delivers water from the holding tank to the refrigerator is noisyA. The pressure switch controlled demand delivery pump is probably delivering morewater than the icemaker can accept (usually about 1/4 gpm at 35 psi), and is momentarilyreaching its shutoff pressure. Use a lower flow pump, and add an accumulator betweenthe pump and refrigerator if necessary. Open the “high voltage drinking water deliverypumps” selection chart, section A, for recommended choices. Q. What effect does feed pressure have on the tank/faucet pressures?A. None. The flow of water to the membrane will increase, but 80 psi pump dischargepressure will not change due to the preset by pass pressure.Q. What effect does higher by-pass pressures have on tank/faucet pressures?A. Since the pressure entering the membrane has increased, so will the pressure exitingthe membrane, at the expense of flow, however. Q. What is the membrane rating based on?A. Based on 95% rejection of TDS levels at 600 ppm and 60 psi membrane feed pressure,in a 70 degree F ambient environment. Q. The boost pump output pressure is only 60psi?A. Assuming you have not adjusted the by pass setting, you may be using a membranewith a permeate production higher than the pump can supply. Either switch to a higherflow pump, or go to a lower rated membrane. Q. Are low feed pressure shut off switches (LPS) available?A. The LPS comes with the appropriate wire harness, but a tee with a 1/8” NPT femalecenter port is not provided. TRANSFORMER Aquatec’s transformers are both current and temperature protected for additional safety protection. Aquatec pump-transformer combinations are designed to operate at maximum efficiency under a wide range of voltage conditions without overheating or overloading. This can save the end-user thousands of kilowatt hours per year compared to less efficient pumps. FeaturesNew Aquatec replacement tranformer for 8800 series booster pumpsDesigned and manufactured by Aquatec to ensure compatibility and proper operationStandard 2-Prong PlugOEM PartSpecificationsInput Voltage: 115-120 VACOutput Voltage Max: 24 VACCord Length: 6 FeetOverload Protection: Thermal Fuse Specification Sheet: Aquatec.com SWITCH Aquatec’s pressure and Vacuum Switches (PSW and VSW Series) provide a full range of in-line pressure sensing electrical switches. These switches, typically mounted near a hydropneumatic holding tank, automatically control the system pump and/or solenoid valve as required. They can also be used to enable hydraulic shut-off valves to operate reliably and positively.Aquatec’s Pressure and Vacuum Switches are normally closed and can be pre-set at various shut-off pressures. If necessary, they can be adapted to operate as normally open switches through minor modifications to the wire terminal connector. The PSW/VSW Series also includes a modular connector for plug-and-play integration with Aquatec’s other system components. FeaturesElectronically shuts off booster pump if feed water is interruptedCompact and inexpensiveHigh Reliability100% factory testedSpecificationsPort Size: 1/4”Pressure: 40PSIVoltage: 250 VAC Specification Sheet: Aquatec.com

Price: 134.99 USD

Location: Peoria, Illinois

End Time: 2024-08-09T16:51:03.000Z

Shipping Cost: 0 USD