Description: 78-88 Regal & Cutlass with 200-4R* Trans Factory Style Shifter Assembly New Reproduction Factory Style Shifter Assembly from GBodyParts!! We have reproduced the Buick Regal and Oldsmobile Cutlass Shifters and made them BETTER than the factory units!!*They have the 2004-R 4 speed set up. (This can easily be put back as a 3 speed by replacing your 3 speed Detent Bracket in place of our 4 speed Detent Bracket) We find out what is wrong with the factory shifters and improve upon them while retaining an exact factory outwards appearance The most common factory shifter issues: Problem: The steel neck with chrome rusts. The top groove where the shifter is Breaks off when the handle cracks.Resolution: Made the neck in Stainless Steel. Much stronger then the OEM mild steel. It is covered with a chrome plating and will never rust. The strength of the stainless you will never snap off the top groove with a bad shifter handle. Problem: shifter cable wears where the pin is attached to by the shifter cable. We have one OEM unit here that must have had a bad cable. The pin was worn half way through.Resolution: Stainless steel pin is welded in and much stronger and will prevent wear. Problem: Stamped Base Metal over time rusts.Resolution: Paint the lower base not leaving it bear like the factory. Problem: J-rod spring flies off an breaks. The spring rusts and loses its tension or splits in half.Resolution: New J rod spring. Slightly upgraded tension for cleaner firmer shifts. Painted so it will not rust. Problem: White J rod adjuster cracks, splits, or wears out easily. Resolution: White plastic with 35 year advanced technology to out last the original and not strip or crack. Problem: J rod bends after all these years of shifting. Will not always go back into alignment of the detent bracket.Resolution: Increased harden steel. Problem: Detent Bracket is worn and not locking in like it used to.Resolution: Stainless detent bracket and painted to appear factory looking. We have been doing shifter parts and handles since 2007. We know what fails on these units and the aggravation of finding some of the parts. No one will sell you just a chrome neck. This unit after testing you fell like you are back in a new car again. The slop is gone and the shifts are tight. If you are restoring and want that new car feel this part is a must. Fits the following center console shifter equipped models with a 200-4R Transmission (Factory Overdrive Transmission from 1983 - 1988):1978 - 1987 Buick: Regal 1978 - 1980 Buick: Century1978 - 1988 Oldsmobile: Cutlass Free shipping within the Contiguous United States
Price: 204.95 USD
Location: Connersville, Indiana
End Time: 2023-11-12T00:28:04.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Country/Region of Manufacture: United States
California Prop 65 Warning: Per California Law (Prop 65) WARNING: This product can expose you to chemicals, including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more info see p65warnings.ca.gov/ Prop 65 is an approved initiative that addresses concerns about exposure to chemicals known to cause cancer, birth defects, or other reproductive harm. To comply with Prop 65, businesses are required to display a warning for listed chemicals unless exposure is low enough to pose “no significant risk” of cancer or is significantly below levels observed to cause birth defects or other reproductive harm. GBodyParts has chosen to display the Prop 65 warning based on the possible presence of one or more listed chemicals, without evaluating the level of exposure
Type: Shifter Assembly
Surface Finish: Plated & Painted
NOTE: Use your original Detent Bracket for 3 speed trans
Fitment Type: Direct Replacement
Manufacturer Part Number: GBO0-PTR-D67-FS
Mounting Hardware Included: No
Brand: Gbodyparts
Manufacturer Warranty: 90 Day
Transmission Type: Automatic
