3mm Animal Feed Pellet Mill MachineBirds Pet Animal Feeder 100-150kg/h 220V

Description: 220V Livestock Feed Pellet Mill Machine 3MM This product model is a new energy-saving product. In the past, the feed was usually processed into powder and then fed, which had some defects such as inconvenient feeding, poor palatability, picky eating of livestock, and low utilization rate. With the advent and popularization of new small pellet feed machinery, powder feed can be easily processed into pellet feed. Lighting electricity can be used as the power to press the granulation from the die hole under the extrusion of the press roller, which can easily adjust the length of the granules. Its structure is simple, the floor area is small, the noise is low, and it has many advantages after processing into pellet feed. Feed granulator is widely used in large, medium and small aquaculture, grain feed processing plants, livestock farms, poultry farms, individual farmers and small and medium-sized farms, farmers or large, medium and small feed processing plants. Note: 1. Before using the machine, it is necessary to adjust the screw of the pressure roller to the appropriate position. The pressure roller and the pressure plate should be closely combined, and the two adjusting screws should be on the same horizontal plane. 2.It is recommended to directly connect to the power supply as much as possible. If the machine is not connected to the power supply, different situations may occur, and the wires are not durable. The wires will gradually burn out over time. 3.Before placing the material into the grinding chamber, the customer needs to stir it well before placing it, otherwise it cannot be made into particles. If it is a dry material, the customer needs to add water or oil to mix it to a certain viscosity before placing it. If it is a wet material with a certain amount of moisture, it can be directly placed into the machine; This machine is equipped with an enlarged and widened discharge port to prevent feed splashing and facilitate the collection of feed by customers. voltage display, which can visually see whether the voltage is stable. Adjustable nut Used to adjust the distance between the pressure roller and the grinding disc. When making pellets, the nuts on the two sides must be balanced to avoid damage to the pressure roller and grinding disc. Enlarge feeding inlet The machine adopts the design of enlarged feed port, which makes it more convenient for you to feed and effectively improves work efficiency. Engine oil filling hole It is recommended to add high-quality machine oil or hyperbola heavy-duty gear oil. The length of feed particlescan be adjusted here by here The machine is equipped with air switch, which is safer to use. Nylon wheels are adopted, which are more wear-resistant and durable. 3mm grinding plates Precautions: 1.When using, it should be noted that there should be no foreign matter such as stones and ironblocks in the raw materials. After the pellet machine has been working continuously for morethan ten shifts, the pressure roller oil hole, the universal joint oil hole, and the linkage shaft oilhole need to be filled with high-temperature lubricating grease to make the pressure roller Goodworking performance and extended bearing life. 2.During granulation, it is strictly forbidden for the pressure roller to contact with the templateto run idly, and the continuous feeding can not be interrupted.At the same time, the pressureroller shaft nut is locked to avoid loosening and damaging the spindle keyway. 3.When granulating, there is no granulation, no discharge, the template should be removed, andafter opening one by one, some fiber feed can be added appropriately to restart the granulation. 4.Always check the tightness of the screws in each part of the machine. If there is oil leakage inthe gearbox, replace the oil seals in time, and check whether the bearings in the machine headare short of oil. 5.When the pellet machine is working, do not reach into the feeding port with your hands. Ifnecessary, use wooden sticks to help feed the pellets. 6.Before turning on the machine, it is necessary to add less material before turning on themachine. When shutting down, leave a small amount of feed in the machine to prevent the pressroller of the machine from contacting the template from idling. 7.If the machine is stuck in operation, stop it immediately, press the pressure roller until thebolt is flat,and then restart the machine. 8.Each time the work is completed, the adjusting pressure roller bolts must be loosened. 9.Iron or stones cannot be put into the griller. 10.Check the elasticity of the belt, and the bearing frequently. Add oil in time when it needs to. Item Number: Livestock Feed Pellet Mill Machine 220V (239195) On May 8, 2024 at 05:31:08 PDT, seller added the following information:

Price: 1130.5 USD

Location: El Monte, California

End Time: 2025-02-03T03:21:32.000Z

Shipping Cost: 0 USD